Need help?


Welcome to our Online Store!


oil diffusion pump made in China

Min.Order Quantity: 1 Set/Sets oil diffusion pump made in China

Supply Ability: 400~700 Set/Sets per Month oil diffusion pump made in China

Payment Terms: L/C,T/T,


  • Product Details
  • Technical Parameters
  • Send Inquiry

Oil diffusion pump Description:

 
KT oil diffusion pump is mainly used to obtain 10-2~10pa high vacuum and ultra-high vacuum state of the main equipment KT oil diffusion pump and valve cooling well pipeline mechanical vacuum pump and other vacuum components together to form a high vacuum pumping system.
 
Oil diffusion pump product features:
 
Diffusion pump oil heated to boiling temperature in the vacuum of the (about 200 degrees) to produce a large amount of oil steam and oil vapor by the nozzle by various directional high-speed nozzle due to the diffusion pump inlet near than steam partial pressure is pumped gas flow, partial pressure of the gas is pumped gas molecules high speed movement in the direction of the steam, gas molecular pump back reflection wall, again by collisions among the steam flow along the wall of steam flow direction flow pump again.After several collisions, the gas molecules are compressed to the low vacuum end, and then the steam ejected from the nozzle of the next several stages is compressed at multiple levels. Finally, the oil vapor is pumped away by the front stage pump, and the oil vapor is condensed on the cooling pump wall and then returned to the lower layer to be heated again, so as to achieve the purpose of air extraction.
 
Oil diffusion pump product advantages:
 
Generally, the performance of diffusion pump is determined by the maximum reverse pressure extraction rate of extreme vacuum and the setting of cold well or low temperature baffle
 
1. Limit vacuum: if the general structure of oil diffusion pump is improved, such as reducing the backflow of oil vapor, additional distillation device, reasonable distribution of heating power, improvement of nozzle Angle design, and oil baffle baffle or cold well adsorption well, the performance of diffusion pump can be greatly improved, and the limit vacuum can reach lower pressure
 
2.Maximum negative pressure: the maximum negative pressure refers to the maximum preposition pressure allowed by the diffusion pump. If the pressure generated by the front stage pump is higher than the maximum negative pressure, the diffusion pump will not work properly
 
3. Pumping rate: the pumping rate of the diffusion pump can be calculated according to the theory of gas molecular motion
 
4.  Set the cold trap and the reasons for the low temperature damper: due to the diffusion pump oil spray nozzle of vapor molecules, most of the condensate pump wall, this is because the outside wall of pump set cooling jacket or because of the cooling pipe wall reflection, but there are a few of vapor molecules are pump scattering returns is pumped space, this kind of phenomenon in the low-temperature laboratory should pay special attention to such as before the diffusion pump and is pumped container with cold trap or low temperature, so you can make the back to add steam is condensed down, as the oil vapor regurgitation the influence factors of oil diffusion pump is as follows
 
1.Oil diffusion pump backflow
 
2.Antidiffusion of gas molecules
 
3. Cracking and decomposition of diffusion pump oil. Generally, the working oil required by diffusion pump is within saturated vapor pressure (about 0.00000001Pa at room temperature)
 
4 pump cleaning is not clean, pollutants in the pump and repeated circulation, affecting its vacuum

 

Item KT-100 KT-160 KT-200 KT-250 KT-300 KT-320 KT-400 KT-500
Ultimate pressure (Pa) 5×10-5
Pumping Capacity (L/S) 550 1800 2800 3500 4600 5000 8500 12000
Critical fore-pump pressure (Pa) 40
Backflow rate mg/(cm2·min) ≤3×10-2
Heating time ( min) ≤30 ≤35 ≤40 ≤45
Heating Power (kw) 0.8-1 1.4-1.6 1.6-1.8 2.2-2.4 2.4-3 4~5 4~5 6~8
Electric Voltage (AC)V 220 380
Pump Oil Model KS-3
Pump Oil Volume ( L) 0.15 0.45 0.55 1-1.4 1-1.6 1.4-1.8 3~4 4
Cooling water consumption (L/H) 180 250 300 350 400 420 500 600
Inlet dimension (mm) 100 160 200 250 300 320 400 500
Outlet dimension (mm) 32 50 65 65 80 80 100 100
Recommended forepump speed (L/s) 4 8 15 15 30 30 70 150
Dimension
(mm)
L(Length) 320 420 530 473 695 725 885 1010
B(Width) 260 315 390 450 505 525 665 815
H(Height) 365 505 575 650 726 830 925 1165
Net weight (kg) 14 31 39 48 89 100 175 185


Fill in your request to get solution & quotation by sales yanyan

Your request will be answered within one working day.

Related Products

Multi stage centrifugal blower

Multi stage centrifugal blower

Product Details

Low price Industrial Circulating water vacuum pump

Low price Industrial Circulating water vacuum pump

Product Details

CL Sereis liquid ring compressor in condenser vacuum

CL Sereis liquid ring compressor in condenser vacuum

Product Details

direct coupled rotary vane Vacuum pump

direct coupled rotary vane Vacuum pump

Product Details